Mr-gasket All Remote Oil Filter System: Single or Dual Manuel d'utilisateur télécharger pdf

GENERAL INFORMATION

Before you begin the installation of this remote oil filter

system kit, please take a few minutes to read the

installation instructions thoroughly.

Work Safely

Perform this installation on a good clean level surface

for maximum safety and protection.

Installation of remote oil filter system requires working

underneath vehicle. Raise front of vehicle by lifting at

points specified by the vehicle manufacturer. Place

blocks or wedges in front of and behind both rear

wheels to prevent movement in either direction.

Support the vehicle with approved automotive support

stands or wheel ramps. Do not use a bumper jack for

supporting vehicle.

IMPORTANT!

To avoid any possibility of bodily injury, do not get

underneath vehicle until you ar confident that it is

safely supported and will not move or fall from its

raised position. Make sure engine is cool to the

touch and oil has cooled sufficiently before

beginning installation.

Tools Required

7/8" Open End Wrench Hammer

3/8" Drill Bit Ratchet

*3/8" Hex Key Wrench Center-Punch

1/2" Open End Wrench Utility Knife

1/2" Socket Electric Hand Drill

Teflon

Thread Seal Tape

(*) Required for Remote Dual Oil Filter System Kits.

Oil Filter By-Pass and Remote

Filter Bracket Mounting

1. Place drain pan underneath oil filter and remove

filter from engine block.

Note: A complete oil change is not necessary for

this installation but is recommended if oil has not

been changed within 2,000 miles.

2. Check by-pass adapter and remote filter mounting

bracket to be sure they are clean and free of any

metal chips or burrs.

3. Insert o-ring into the groove located in oil filter

by-pass adapter. Lubricate top of o-ring using a

light film of oil. Spin by-pass adapter onto engine

block until snug, then tighten an additional 3/4

to 1 full turn same as the stock oil filter (Refer

to illustration).

4. Select the best location for remote oil filter

mounting bracket. The firewall, fenderwell, or frame

rail are convenient locations. Be sure oil filter has

sufficient ground clearance and mark location for

remote bracket with a grease pen or scribe.

Note: Remote oil filter bracket can be mounted

vertically or horizontally whichever is most

convenient for your application.

5. Before starting, measure distance between by-

pass adapter on engine block and remote oil filter

bracket. One length (60") of high temperature hose

is supplied to complete the connections. This hose

must be cut in two (2) individual lengths. Before

cutting, make sure remote oil filter mounting

bracket is located close enough to the by-pass

adapter.

For installations that require more hose length,

Mr. Gasket has available a 96" length of hose

part no. 7697, this will allow using two (2) lengths

of hose up to 48" each for these applications.

6. Use the remote oil filter mounting bracket as a

template and mark mounting holes with a grease

pen or scribe. Center-punch hole locations and

make sure underside is free and clear from any

obstructions. Drill three (3) 3/8" holes through

surface and debur holes.

7. Place remote oil filter bracket onto mounting

location and attach using 5/16" hex head bolts,

flat washers, and lock-nuts supplied. Tighten all

nuts and bolts securely.

Note: The dual remote oil filter mounting bracket

requires installing hex head bolts through bracket

from the back side.

REMOTE OIL FILTER SYSTEM

SINGLE OR DUAL OIL FILTER APPLICATIONS

INSTALLATION INSTRUCTIONS

NOT RECOMMENDED FOR MARINE OR DIESEL APPLICATIONS

FORM 97140111 08/04

Visit us on the web at: www.mrgasket.com

1 2 3 4

Résumé du contenu

Page 1 - REMOTE OIL FILTER SYSTEM

GENERAL INFORMATIONBefore you begin the installation of this remote oil filtersystem kit, please take a few minutes to read theinstallation instructio

Page 2 - OIL FILTER RECOMMENDATIONS

Oil Hose Assembly and Fitting InstallationIMPORTANT!Keep hose as short as possible when routing. Hosemust not kink, crimp, contact hot exhaust or shar

Page 3 - Installation

Page 4 - Technical Service

Single Oil Filter KitDescription QtyDual Oil Filter KitDescription QtyContents of Remote Oil Filter System KitsNote: Retain this instruction sheet for

Commentaires sur ces manuels

Pas de commentaire

Mr-gasket All Remote Oil Filter System: Single or Dual Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Mr-gasket All Remote Oil Filter System: Single or Dual. Mr. Gasket All Remote Oil Filter System: Single or Dual User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Mr-gasket All Remote Oil Filter System: Single or Dual